Tap WaterIndex

← Alaska

Tap water quality report

Quickdraw h2o

EPA monitoring tested this supplier for 10 contaminants and detected 10. A detection doesn't automatically mean the water is unsafe — the level and EPA source for each is below.

10
contaminants tested
10
detected
100
people served
0
health-based violations
Alaska rankingsLead in AlaskaPFAS in Alaska
Water source
SWP
Ownership
Private
Counties served
Kenai Peninsula Borough

Compliance record

Formal violations the EPA has on file for this supplier. A health-based violation means a contaminant limit or a required treatment was breached; the rest are monitoring or reporting failures — still violations, but not a measured health risk.

0
health-based violations
3
violations on file
0
still open
ViolationTypeStatusPeriod
Other Monitoring Resolved 2014-07-01
MR Monitoring Resolved 2014-01-01 → 2014-12-31
MR Monitoring Resolved 2014-01-01 → 2014-12-31

Other contaminants detected

Each bar shows the measured level as a share of the EPA limit: green is well under, amber is close to it, red is over. For lead and copper the limit applies to exactly the 90th-percentile figure shown, so red there means a real exceedance. For everything else the limit applies to a running annual average while the figure is the 95th percentile of this system's samples — over 100% is worth reading, but is not by itself a violation. Where a single sample came in higher than that percentile, it is noted under the bar. Formal violations are listed separately.
ContaminantLevel vs EPA limitDetection rateSourcePeriod
Bromodichloromethane
7.27 µg/L
No EPA limit set
worst single sample: 7.29 µg/L
9/9 SYR4 2015–2019
Dibromochloromethane
3.034 µg/L
No EPA limit set
worst single sample: 3.23 µg/L
8/8 SYR4 2015–2019
Total Haloacetic Acids (HAA5)
34.25 µg/L 57%
of the EPA limit 60 µg/L
worst single sample: 35 µg/L
6/6 SYR4 2017–2019
Chloroform
27.3 µg/L
No EPA limit set
worst single sample: 27.7 µg/L
5/5 SYR4 2016–2019
Trichloroacetic Acid
15.8 µg/L
No EPA limit set
worst single sample: 17 µg/L
5/5 SYR4 2015–2018
Bromoform
2.358 µg/L
No EPA limit set
worst single sample: 2.4 µg/L
4/4 SYR4 2015–2019
TTHM
28.9885 µg/L 36%
of the EPA limit 80 µg/L
worst single sample: 32.8 µg/L
4/4 SYR4 2017–2019
Dibromoacetic Acid
1.18 µg/L
No EPA limit set
worst single sample: 1.2 µg/L
3/3 SYR4 2016–2018
Dichloroacetic Acid
15.9 µg/L
No EPA limit set
worst single sample: 16 µg/L
3/3 SYR4 2015–2019
Monochloroacetic Acid
2.96 µg/L
No EPA limit set
worst single sample: 3 µg/L
2/2 SYR4 2015–2019

Utility contact

Contact
MOORE, JR, LLOYD
Phone
907-235-8837
Email
[email protected]

Frequently asked questions about Quickdraw h2o

Is Quickdraw h2o tap water safe to drink?

EPA monitoring detected 10 contaminants in Quickdraw h2o's water. A detection isn't the same as a violation — most levels are within federal limits. See each level and source above, and the utility's annual Consumer Confidence Report for its official compliance status.

What contaminants were detected in Quickdraw h2o's water?

EPA monitoring detected Bromodichloromethane, Dibromochloromethane, Total Haloacetic Acids (HAA5), Chloroform, Trichloroacetic Acid, and others. The full list with the level and data source for each is above.

How many people does Quickdraw h2o serve?

Quickdraw h2o reports serving 100 people in Alaska, per its EPA record.

Has Quickdraw h2o had any water quality violations?

The EPA has 3 violations on file for Quickdraw h2o, of which 0 are health-based (a contaminant limit or required treatment was breached) and 0 remain open. The rest are monitoring or reporting failures.

Where does this data come from?

Every figure is official EPA drinking-water monitoring — the Lead & Copper Rule, the UCMR-5 nationwide testing program, and the EPA Six-Year Review — not our own testing. Each number is labelled with its source and period.